Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 92 / 170

Section 5 - Maintenance

Page 84

90-8M0050539

eng

MAY 2011

b. Proper fluid level with engine cold should be within the cold range.

a -

Power steering pump

b -

Cold range

c -

Warm range

3. Fill to full line with specified fluid.

IMPORTANT: If fluid is not visible in pump, contact your authorized Mercury MerCruiser dealer.

Filling

1. Remove the fill cap/dipstick and observe the level.
2. Add Quicksilver Power Trim and Steering Fluid or Dexron III Automatic Transmission Fluid (ATF) to bring the fluid level up to

the proper level.

Tube Ref No.

Description

Where Used

Part No.

114

Power Trim and Steering

Fluid

Power steering system

92-858074K01

3. Reinstall the fill cap/dipstick.

Changing

Power steering fluid does not require changing unless it becomes contaminated with water or debris. Contact your authorized

Mercury MerCruiser dealer.

Engine Coolant—350/377 MAG ECT and SeaCore 350/377 MAG ECT

Checking

CAUTION

A sudden loss of pressure can cause hot coolant to boil and discharge violently resulting in serious injury from burns. Allow the

engine to cool down before removing the coolant pressure cap.

6100

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды