Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 123 / 170

Section 5 - Maintenance

90-8M0050539

eng

MAY 2011

Page 115

Flushing Attachments

Flushing Device

91‑44357Q 2

9192

Attaches to the water intakes; provides a fresh water connection when flushing the

cooling system or operating the engine.

Sterndrive Water Pickups

This Mercury MerCruiser sterndrive is equipped with side water pickups. Side pickups require the flushing attachment (44357Q

2).

5773

Side Pickup

NOTE: Flushing is needed only for salty, brackish, mineral‑laden, or polluted water applications. Flushing is recommended after

each outing for best results.

NOTICE

Flushing the engine with the boat in the water can cause seawater to flow into the engine, resulting in engine damage. Close

the seacock before flushing the engine. Keep the seacock closed until starting the engine.

1. On models with the sterndrive seawater inlet blocked, supply water to the sterndrive and to the engine. See

Alternative Water

Pickups

2. On models using the sterndrive water pickups for water supply: proceed to Step 3. or Step 4.

NOTE: Closed cooled models are equipped with a heat exchanger on the engine.

3. If flushing the cooling system with the boat in the water:

a. Raise the sterndrive to trailer position.
b. Install the appropriate flushing attachment over the water inlet holes in the gear housing.
c. Lower sterndrive to full down/in position.

4. If flushing the cooling system with the boat out of the water:

a. Lower sterndrive to full down/in position.

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed. Before

installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the engine from

starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды