Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 77 / 170

Section 4 - Specifications

90-8M0050539

eng

MAY 2011

Page 69

377 MAG, SeaCore 377 MAG

NOTE: Performance specifications are obtained and corrected in accordance with SAE J1228/ISO 8665 Crankshaft Power.

All measurements are taken with the engine at normal operating temperature.

RPM range is measured using an accurate service tachometer with the engine at normal operating temperatures.

Oil pressure must be checked with the engine at normal operating temperature.
NOTE: Oil pressure specifications are for reference and may vary.

IMPORTANT: Do not mix spark plug types in an engine. All spark plugs should have the same part number.

Propshaft power

293 kW (320 hp)

Displacement

6.2 L (377 cid)

Alternator amperage

Hot

72 A

Cold

65 A

RPM

WOT

4800–5200

Rev limiter

5350

Idle in neutral

550

Minimum oil pressure

At 2000 RPM

124 kPa (18 psi)

At idle

41 kPa (6 psi)

Thermostat

Seawater‑cooled models

71° C (160° F)

MPI models with closed cooling

77° C (170° F)

Timing at idle

Not Adjustable

Firing order

1‑8‑4‑3‑6‑5‑7‑2

Minimum battery rating

Non‑DTS models

750 CCA, 950 MCA, 180 Ah

DTS models

800 CCA, 1000 MCA, 190 Ah

Spark plug type

AC Platinum (AC 41‑993)
AC Platinum (AC 41‑101)

Spark plug gap

1.5 mm (0.060 in.)

Emission control system

Electronic engine control (EC)

Fluid Specifications

IMPORTANT: All capacities are approximate fluid measures.

Engine—350/377 MAG ECT and SeaCore 350/377 MAG ECT

IMPORTANT: Always use the dipstick to determine the exact quantity of oil or fluid required.

All Models

Capacity

Fluid Type

Engine oil (with filter)

4.25 L (4.50 US qt)

Mercury Full‑Synthetic MerCruiser Engine Oil 20W‑40

Seawater cooling system (winterization

use only)

20 L (21 US qt)

Propylene glycol and purified water

Closed cooling system

18 L (19 US qt)

Mercury Extended Life Coolant Antifreeze or extended life

ethylene glycol 5/100 antifreeze mixed 50/50 with purified water

Engine—350/377 MAG and SeaCore 350/377 MAG

IMPORTANT: Always use the dipstick to determine the exact quantity of oil or fluid required.

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды