Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 74 / 170

Section 4 - Specifications

Page 66

90-8M0050539

eng

MAY 2011

Firing order

1‑8‑4‑3‑6‑5‑7‑2

Minimum battery rating

Non‑DTS models

750 CCA, 950 MCA, 180 Ah

DTS models

800 CCA, 1000 MCA, 190 Ah

Spark plug type

AC Platinum (AC 41‑993)
AC Platinum (AC 41‑101)

Spark plug gap

1.5 mm (0.060 in.)

Emission control system

Electronic control (EC), heated oxygen sensor

(HO2S), catalyst

377 MAG ECT, SeaCore 377 MAG ECT

NOTE: Performance specifications are obtained and corrected in accordance with SAE J1228/ISO 8665 Crankshaft Power.

All measurements are taken with the engine at normal operating temperature.

RPM range is measured using an accurate service tachometer with the engine at normal operating temperatures.

Oil pressure must be checked with the engine at normal operating temperature.
NOTE: Oil pressure specifications are for reference and may vary.

IMPORTANT: Do not mix spark plug types in an engine. All spark plugs should have the same part number.

Propshaft power

293 kW (320 hp)

Displacement

6.2 L (377 cid)

Alternator amperage

Hot

72 A

Cold

65 A

RPM

WOT

4800–5200

Rev limiter

5350

Idle in neutral

550

Minimum oil pressure

At 2000 RPM

124 kPa (18 psi)

At idle

41 kPa (6 psi)

Thermostat

Seawater‑cooled models

71° C (160° F)

MPI models with Closed Cooling

77° C (170° F)

Timing at idle

Not Adjustable

Firing order

1‑8‑4‑3‑6‑5‑7‑2

Minimum battery rating

Non‑DTS models

750 CCA, 950 MCA, 180 Ah

DTS models

800 CCA, 1000 MCA, 190 Ah

Spark plug type

AC Platinum (AC 41‑993)
AC Platinum (AC 41‑101)

Spark plug gap

1.5 mm (0.060 in.)

Emission control system

Electronic control (EC), heated oxygen sensor

(HO2S), catalyst

350/377 MAG and SeaCore 350/377 MAG—Specifications

Fuel Requirements

IMPORTANT: Use of improper gasoline can damage your engine. Engine damage resulting from the use of improper
gasoline is considered misuse of the engine and any resulting damage will not be covered under the limited warranty.

Fuel Ratings

Mercury MerCruiser engines will operate satisfactorily when using a major brand of unleaded gasoline meeting the following

specifications:

USA and Canada—

having a posted pump Octane Rating of 87 (R+M)/2 minimum. Premium gasoline 92 (R+M)/2 Octane is also

acceptable. Do not use leaded gasoline.

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды