Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 103 / 170

Section 5 - Maintenance

90-8M0050539

eng

MAY 2011

Page 95

1. Remove the PCV valve from the port valve cover.

a -

PCV valve (hose not shown)

2. Disconnect the PCV valve from the hose and discard the valve.
3. Install a new PCV valve in the valve cover and reconnect the hose.
4. Ensure that the PCV valve is tightly seated in the valve cover.

Cleaning the IAC Muffler

WARNING

Fuel is flammable and explosive. Ensure that the key switch is off and the lanyard is positioned so that the engine cannot start.

Do not smoke or allow sources of spark or open flame in the area while servicing. Keep the work area well ventilated and avoid

prolonged exposure to vapors. Always check for leaks before attempting to start the engine, and wipe up any spilled fuel

immediately.

NOTE: The IAC muffler may be installed in the throttle body or in the IAC adapter. Locate your IAC muffler by removing the engine

cover.

1. Remove the engine cover.
2. Remove the IAC muffler.

33269

IAC muffler installed in the IAC adapter

3. Inspect the IAC muffler for holes, cracks, or deterioration. Replace the IAC muffler if damaged.

IMPORTANT: Do not get cleaner on electrical connections and do not use cleaner containing methyl ethyl ketone.

4. Clean the IAC muffler with warm water and a mild detergent. Replace if necessary.
5. Allow the IAC muffler to dry completely, and then install.

33143

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды