Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 121 / 170

Section 5 - Maintenance

90-8M0050539

eng

MAY 2011

Page 113

IMPORTANT: If anti‑fouling protection is required for the boat hull or boat transom, you can use copper‑based paint if it is not

prohibited by law. If you are using copper based anti‑fouling paint, observe the following precaution:
•

Avoid an electrical interconnection between the Mercury MerCruiser Product, Anodic Blocks, or MerCathode System and the

paint by allowing a minimum of 40 mm (1‑1/2 in.) UNPAINTED area on transom of the boat around these items.

a -

Painted boat transom

b -

Minimum 40 mm (1‑1/2 in.) unpainted area around transom

assembly

NOTE: Sterndrive and transom assembly can be painted with a good marine paint or an anti‑fouling paint that DOES NOT

contain copper or any other material that could conduct electrical current. Do not paint drain holes, anodes, the MerCathode

system or items specified by the boat manufacturer.

NOTICE

Washing the MerCathode assembly can damage components and lead to rapid corrosion. Do not use any cleaning equipment

such as brushes or high‑pressure washers to clean the MerCathode assembly.

Do not power‑wash a sterndrive that has a MerCathode assembly. Doing so can damage the coating on the reference wire of the

MerCathode assembly and increase corrosion.

a -

Reference electrode

b -

Anode plate

8107

21563

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды