Mercury Inboard 5.7L Скачать руководство пользователя страница 78

Страница: 78 / 82

Troubleshooting

Page 70

90-860174050 JUNE 2005

Remote Control Operates Hard, Binds, Has Excessive Free‑play Or

Makes Unusual Sounds

Possible Cause

Remedy

Insufficient lubrication on shift and throttle linkage

fasteners.

Lubricate.

Obstruction in shift or throttle linkages.

Remove obstruction.

Loose or missing shift and throttle linkages.

Check all throttle linkages. If any are loose or missing,

see authorized Mercury MerCruiser dealer

immediately.

Shift or throttle cable kinked.

Straighten cable or have authorized Mercury

MerCruiser dealer replace cable if damaged beyond

repair.

Steering Wheel Turns Hard Or Jerky

Possible Cause

Remedy

Low power steering pump fluid level.

Check for leak. Refill system with fluid.

Drive belt loose or in poor condition.

Replace and/or adjust.

Insufficient lubrication on steering components. Lubricate.

Loose or missing steering fasteners or parts.

Check all parts and fasteners if any are loose or missing,

see authorized Mercury MerCruiser dealer immediately.

Contaminated power steering fluid.

See authorized Mercury MerCruiser dealer.

Содержание Inboard 5.7L



















































































Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды

Mercury Inboard 5.7L, Руководство пользователя

Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды