Mercury Inboard 5.7L Скачать руководство пользователя страница 72

Страница: 72 / 82

Storage

Page 64

90-860174050 JUNE 2005

Check valve

6131

a -

Drain plug (if equipped)

3. On models with a seawater pickup pump, remove the two blue drain plugs. If the

seawater pickup pump does not have blue drain plugs, or you are unable to access

them, loosen the clamps and remove both hoses.

6145

a -

Hose clamps

b -

Blue drain plugs

4. Crank the engine over slightly with starter motor to purge any water trapped in the

seawater pickup pump. Do not allow the engine to start.

5. After the cooling system has been drained completely, install the drain plugs, reconnect

hoses, and tighten all hose clamps securely.

Battery Storage

Whenever the battery will be stored for an extended period of time, be sure the cells are

full of water and the battery is fully charged and in good operating condition. It should be

clean and free of leaks. Follow the battery manufacturer's instructions for storage.

Power Package Recommissioning

1. Ensure that all cooling system hoses are connected properly and hose clamps are tight.

CAUTION

Avoid electrical system damage. When installing the battery, be sure to connect the

negative (‑) battery cable to the negative (‑) battery terminal and the positive (+) battery

cable to the positive (+) battery terminal.

2. Install a fully charged battery. Clean the battery cable clamps and terminals and

reconnect cables. Tighten each cable clamp securely when connecting.

Содержание Inboard 5.7L



















































































Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды

Mercury Inboard 5.7L, Руководство пользователя

Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды