manualshive.com logo in svg

Mercury Inboard 5.7L, Руководство пользователя

Поделиться
Скачать
Mercury Inboard 5.7L Скачать руководство пользователя страница 25

Getting to Know Your Power Package

90-860174050   JUNE  2005

Page  17

4. A 20 amp fuse is located near the TKS module on the carburetor. This fuse provides

protection to the wiring of the TKS module if an electrical overload occurs.

11822

Audio Warning System

Your Mercury MerCruiser power package may be equipped with an Audio Warning System.

The Audio Warning System will not protect the engine from damage. It is designed to warn

the operator that a problem has occurred.
The audio warning system will sound with a continuous horn if one of the following occurs:
• Engine oil pressure too low
• Engine temperature too hot
• Seawater pressure too low
The audio warning system will sound with an intermittent beeping if the following occurs:
• Transmission fluid temperature too hot

!

 CAUTION

Operation of the engine after the audio warning system alarm has sounded could result

in damage to the power package. Do not operate engine once the alarm has sounded

except to avoid a hazardous situation.

If  the  alarm  sounds,  stop  the  engine  immediately.  Investigate  cause  and  correct  it,  if

possible. If the cause cannot be determined, contact your authorized Mercury MerCruiser

dealer.

Testing The Audio Warning System

1. Turn the ignition switch to the "ON" position without cranking the engine.
2. Listen for the audio alarm. The alarm will sound if the system is functioning correctly.

Содержание Inboard 5.7L



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды