Mercury Inboard 5.7L Скачать руководство пользователя страница 65

Страница: 65 / 82

Maintenance

90-860174050 JUNE 2005

Page 57

Models with Water V‑Drive Transmissions: Disconnect water inlet hose from the

transmission fitting. Using appropriate connector, connect water hose to water

source. Proceed to Step 3.

6091

All other models: Using appropriate connector, connect the flushing hose from the

water source to the water inlet hose (upper hose) of the seawater pickup pump.

Proceed to Step 3.

6092

WARNING

Contact with moving drive components and the propeller can cause personal injury or

death. To avoid possible injury, remove the propeller and ensure that no people or

animals are in the area of the drive unit while flushing.

2. If flushing the engine with the boat out of the water, remove the propeller. Refer to boat

manufacturers' instructions.
a.

Models with Walter V‑Drive Transmissions: Disconnect water inlet hose from

transmission fitting. Using appropriate connector, connect the flushing hose.

Proceed to Step 3.

6091

Содержание Inboard 5.7L



















































































Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды

Mercury Inboard 5.7L, Руководство пользователя

Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды