manualshive.com logo in svg

Mercury Inboard 5.7L, Руководство пользователя

Поделиться
Скачать
Mercury Inboard 5.7L Скачать руководство пользователя страница 42

Specifications 

Page  34

90-860174050   JUNE  2005

Cruising RPM

Modern inboard engines operate at higher engine speeds than those produced just a few

years ago. This increased RPM along with better breathing is largely responsible for the

significant increase in horsepower of these new engines. Along with the higher WOT RPM

comes higher cruising RPM. This higher RPM is critical for optimum performance and

efficiency. The materials and design of the new engines allow these higher speeds without

durability penalty. In fact, over‑propping the boat to reduce the cruising RPM to previous

levels will increase the susceptibility to engine damage from detonation and pre‑ignition.

The recommended cruising RPM ranges are:

Cruising RPM for Peak Efficiency

Model

RPM Range

5.7L

3200‑3600

Fuel Requirements

IMPORTANT:  Use  of  improper  gasoline  can  damage  your  engine.  Engine  damage

resulting  from  the  use  of  improper  gasoline  is  considered  misuse  of  the  engine,  and

damage caused thereby will not be covered under the limited warranty.

Fuel Ratings

Mercury  MerCruiser  engines  will  operate  satisfactorily  when  using  a  major  brand  of

unleaded gasoline meeting the following specifications:
USA and Canada ‑ having a posted pump Octane Rating of 87 (R+M)/2 minimum. Premium

gasoline [92 (R+M)/2 Octane] is also acceptable. Do not use leaded gasoline.
Outside USA and Canada ‑ having a posted pump Octane Rating of 90 RON minimum.

Premium gasoline (98 RON) is also acceptable. If unleaded gasoline is not available, use

a major brand of leaded gasoline.

Using Reformulated (Oxygenated) Gasolines (USA Only)

This type of gasoline is required in certain areas of the USA. The 2 types of oxygenates

used  in  these  fuels  is  Alcohol  (Ethanol)  or  Ether  (MTBE  or  ETBE).  If  Ethanol  is  the

oxygenate that is used in the gasoline in your area, refer to Gasolines Containing Alcohol.
These Reformulated Gasolines are acceptable for use in your Mercury MerCruiser engine.

Gasolines Containing Alcohol

If the gasoline in your area contains either methanol (methyl alcohol) or ethanol (ethyl

alcohol), you should be aware of certain adverse effects that can occur. These adverse

effects are more severe with methanol. Increasing the percentage of alcohol in the fuel can

also worsen these adverse effects.
Some of these adverse effects are caused because the alcohol in the gasoline can absorb

moisture from the air, resulting in a separation of the water/alcohol from the gasoline in the

fuel tank.
The fuel system components on your Mercury MerCruiser engine will withstand up to 10%

alcohol content in the gasoline. We do not know what percentage your boat's fuel system

will withstand. Contact your boat manufacturer for specific recommendations on the boat's

fuel  system  components  (fuel  tanks,  fuel  lines,  and  fittings).  Be  aware  that  gasolines

containing alcohol may cause increased:
• Corrosion of metal parts
• Deterioration of rubber or plastic parts

Содержание Inboard 5.7L



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды