manualshive.com logo in svg

Mercury Inboard 5.7L, Руководство пользователя

Поделиться
Скачать
Mercury Inboard 5.7L Скачать руководство пользователя страница 63

Maintenance

90-860174050   JUNE  2005

Page  55

7. While  holding  the  adjustment  stud  at  the  correct  belt  tension,  tighten  the

16 mm (5/8 in.) locking nut.

a

b

6119

a -

8 mm (1/16 in.) adjusting stud

b -

16 mm (5/8 in.) locking nut

8. Operate the engine for a short period of time and recheck the belt adjustment.

Flushing The Power Package

Inboards

NOTE:  Flushing  is  needed  only  for  salty,  brackish,  mineral  laden  or  polluted  water

applications. Flushing is recommended after each outing for best results.

1. Close the seacock, if equipped, or remove the water inlet hose and plug the inlet.
2. Drain the seawater from the engine.
3. Attach the quick connect fitting to a water hose.
4. Open the water source completely.
5. Remove the blue cap from the flush socket on the engine

!

 CAUTION

Overheating from insufficient cooling water will cause engine and drive system damage.

Ensure that there is sufficient water always available at water inlet holes during operation.

!

 CAUTION

Do not let water run more than 15 seconds with engine not operating or too much flushing

water will collect in the muffler.

Содержание Inboard 5.7L



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды