Mercury Inboard 5.7L Скачать руководство пользователя страница 44

Страница: 44 / 82

Specifications

Page 36

90-860174050 JUNE 2005

NOTE: The use of non‑detergent oils, multi‑viscosity oils (other than as specified), non

FC‑W rated synthetic oils, low quality oils or oils that contain solid additives are specifically

not recommended.

Engine Specifications

Models

5.7L Inboard

5.7L Tow Sport

Horsepower

260

270

Kilowatts

194

201

Displacement

5.7 L (350 cid)

Specified WOT RPM Range

4200‑4600

4400‑4800

Idle RPM in Neutral

650

Minimum Oil Pressure @ Idle

41 kPa (6 psi)

Minimum Oil Pressure @ 2000 RPM

124 kPa (18 psi)

Thermostat

71° C (160° F)

Timing @ Idle

10° BTDC

Firing Order

1‑8‑4‑3‑6‑5‑7‑2

Electrical System

12 Volt Negative (‑) Ground

Alternator Rating ‑ Hot Operating Amps

65 amp

Alternator Rating ‑ Cold Operating Amps

72 amp

Recommended Battery Rating (Minimum)

375 CCA, 475 MCA, or 90 Ah

1. Performance obtained and corrected in accordance with SAE J1228/ISO 8665 Crankshaft Power.

2. Measured using an accurate service tachometer with the engine at normal operating temperatures

3. A special procedure must be followed to adjust idle rpm. Consult your Authorized Mercury MerCruiser Dealer before attempting

this procedure.

4. Oil pressure must be checked with the engine at normal operating temperature.

Содержание Inboard 5.7L



















































































Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды

Mercury Inboard 5.7L, Руководство пользователя

Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды