Mercury Inboard 5.7L Скачать руководство пользователя страница 32

Страница: 32 / 82

On The Water

Page 24

90-860174050 JUNE 2005

Good Ventilation

Ventilate the passenger area, open the side curtains or forward hatches to remove fumes.
1. Example of desired air flow through the boat.

mc79553-1

Poor Ventilation

Under certain conditions, permanently enclosed or canvas enclosed cabins or cockpits with

insufficient ventilation may draw in carbon monoxide. Install one or more carbon monoxide

detectors in your boat.
Although the occurrence is rare, on a very calm day, swimmers and passengers in an open

area of a stationary boat that contains or is near an operating engine may be exposed to

a hazardous level of carbon monoxide.
1. Examples of poor ventilation while a boat is stationary:

mc79554-1

a -

Operating the engine when the

boat is moored in a confined space

b -

Mooring close to another boat with

its engine operating

2. Examples of poor ventilation while a boat is moving:

mc79556-1

a -

Operating the boat with the trim

angle of the bow too high

b -

Operating the boat with no forward

hatches open (station wagon effect)

Basic Boat Operation

Launching and Boat Operation

IMPORTANT: Install bilge drain plug prior to launching boat.

CAUTION

To avoid possible ingestion of water that can damage engine components, do not turn

the ignition key off when the engine is above idle speed. When launching your boat from

a steep ramp, enter the water slowly. Do not use the lanyard stop switch to shut off the

engine above idle speed. When coming off plane, if a large following wave may roll over

the boat's transom, apply a short, light burst of throttle to minimize the wave action against

the stern of the boat. Do not come off plane quickly, shift into reverse and shut off engine.

Содержание Inboard 5.7L



















































































Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды

Mercury Inboard 5.7L, Руководство пользователя

Результаты поиска

Содержание Inboard 5.7L

Отзывы:

Бренды по названию

Популярные бренды