Mercury 1997 Sable Скачать руководство пользователя страница 78

Страница: 78 / 167

Do not park, idle, or drive your vehicle in
dry grass or other dry ground cover. The

emission system heats up the engine compartment
and exhaust system, which can start a fire.

Do not start your vehicle in a closed garage
or in other enclosed areas. Exhaust fumes

can be toxic. Always open the garage door before
you start the engine. See

Guarding against

exhaust fumes

in this chapter for more

instructions.

If you smell exhaust fumes inside your
vehicle, have your dealer inspect your

vehicle immediately. Do not drive if you smell
exhaust fumes.

STARTING THE ENGINE

1. Turn the key to 5
(Start) without
pressing the
accelerator. The key
will return to 4 (On).

2. If the engine does not start within five seconds,
wait ten seconds and try again.

3. If the engine does not start in two attempts OR
the temperature is below —12°C (10°F), depress
accelerator and start the engine while holding the
accelerator down. Release accelerator when engine
starts.

com_starting_vehicle.01

Starting

Содержание 1997 Sable








































































































































































Результаты поиска

Содержание 1997 Sable

Отзывы:

Бренды по названию

Популярные бренды

Mercury 1997 Sable, Руководство пользователя

Результаты поиска

Содержание 1997 Sable

Отзывы:

Бренды по названию

Популярные бренды