manualshive.com logo in svg

Mercury 1997 Sable, Руководство пользователя

Поделиться
Скачать
Mercury 1997 Sable Скачать руководство пользователя страница 7

Safety belt

Illuminates when the
ignition is switched on
to remind you to fasten
your safety belts. For
more information, refer to

Using the safety

restraints properly

in the

Seating and safety

restraints

chapter.

Door ajar

Illuminates when the
ignition switch is in the
ON or START position
and any door is open.

Service engine soon

This light illuminates
when the engine’s
Emission Control
System requires
service. It will also
illuminate when the ignition key is in the ON
position and the engine is off.

Low fuel

If the fuel gauge
reaches approximately
1/16th of a tank, this
lamp will illuminate.
The ignition must be turned on for this lamp to
illuminate.

Low coolant (if equipped)

This lamp will
illuminate when the
engine coolant inside
the reservoir is low.
This lamp will come on
when the ignition is first turned on, but then should
turn off. If the lamp stays on and a chime sounds,

SERVICE

ENGINE

SOON

LOW

COOLANT

com_door-ajar.02

dno_service-engine

dno_low-fuel

dno_low-coolant

Instrumentation

7

Содержание 1997 Sable








































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды