Mercury 1997 Sable Скачать руководство пользователя страница 111

Страница: 111 / 167

3. Connect the positive
(+) terminal of the
discharged battery (1)
to the positive (+)
terminal of the booster
battery (2).

4. Connect one end of
the second lead to the
negative (-) terminal of
the booster battery (3)
and the other end to a
metal part of the
engine to be started (4), not to the negative (-)
terminal of the discharged battery.

5. Make sure that the jump leads are clear of moving
parts of the engine.

Do not connect the end of the second cable
to the negative ([-]) terminal of the battery

to be jumped. A spark may cause an explosion of
the gases that surround the battery.

JUMP STARTING

1. Start the booster vehicle and run the engine at
moderately increased speed.

2. Start the engine of the vehicle with the
discharged battery.

3. Once the engine has been started, run both
vehicles for a further three minutes before
disconnecting the leads.

–

com_jump_starting.01

com_removing_cables.01

Roadside emergencies

111

Содержание 1997 Sable








































































































































































Результаты поиска

Содержание 1997 Sable

Отзывы:

Бренды по названию

Популярные бренды

Mercury 1997 Sable, Руководство пользователя

Результаты поиска

Содержание 1997 Sable

Отзывы:

Бренды по названию

Популярные бренды