manualshive.com logo in svg

Mercury 1997 Sable, Руководство пользователя

Поделиться
Скачать
Mercury 1997 Sable Скачать руководство пользователя страница 30

Central locking/Two step unlocking

When unlocking the driver or front passenger door
with the key, turn it once toward the front of the
vehicle to unlock that door only. Turn the key a
second time to unlock all doors. When locking, turn
the key toward the back of the vehicle to lock all
doors.

Liftgate (wagon only)

The power liftgate lock
is located on the right
inside trim panel in the
cargo area. When this
lock is pressed, all
doors and the liftgate
will lock.

POWER SIDE VIEW MIRRORS

To change mirror
position, first select a
mirror by moving the
selector control left
(

) or right (

),

then moving the
control to set the
desired position.

Power heated side view mirrors (if equipped)

The heated mirrors will melt frost, thin ice or
remove fog when the rear window defroster is
activated.

dno_liftgate-locking

dno_power-mirrors

dno_mirrors

dno_child-locks

Controls and features

30

Содержание 1997 Sable








































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды