manualshive.com logo in svg

Mercury 1997 Sable, Руководство пользователя

Поделиться
Скачать
Mercury 1997 Sable Скачать руководство пользователя страница 110

the key, send the registration card to the
manufacturer (not the dealer) to get a replacement
key. If the lug wrench/lug nut key assembly is lost,
see your nearest Ford or Lincoln/Mercury dealer
who has access to the master set of keys.

Do not

use an impact wrench with the anti-theft key.

JUMP STARTING YOUR VEHICLE

The gases around the battery can explode if
exposed to flames, sparks, or lit cigarettes.

An explosion could result in injury or vehicle
damage.

Do not push-start your vehicle. You could
damage the catalytic converter. For further

information, see

Jumper Cables

in the Index.

Batteries contain sulfuric acid which burns
skin, eyes, and clothing.

CONNECTING THE JUMPER CABLES

1. Position the vehicles so that they do not touch
one another.

2. Switch off the engine. Switch off any unnecessary
electrical equipment.

com_jump-starting.01

com_connecting_cables.01

Roadside emergencies

110

Содержание 1997 Sable








































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды