manualshive.com logo in svg

Mercury 1997 Sable, Руководство пользователя

Поделиться
Скачать
Mercury 1997 Sable Скачать руководство пользователя страница 28

The dome lamp will
stay on if the control is
moved to the ON
position. When the
control is in the DOOR
position, the lamp will
only come on when a
door is opened. If the
control is moved to the
OFF position, the lamp will not come on at all.

The dome lamp will illuminate whenever a front
door is opened. If either front door has been opened
from the outside, the lamp will remain on for 25
seconds after the door is shut. If any other door has
been opened from the inside, the lamp will shut off
immediately after the door is closed.

The map lamps and
controls are located on
the dome lamp. Press
the controls on either
side of each map lamp to activate the lamps.

If equipped with a
moon roof, the map
lamps are located on
the moon roof control
panel. Press LIGHT to
illuminate the map
lamp.

OFF    DOOR    ON

TILT

LIGHT

LIGHT

SLIDE

dno_pwr-windows

Controls and features

28

Содержание 1997 Sable








































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды