manualshive.com logo in svg

Mercury 1997 Sable, Руководство пользователя

Поделиться
Скачать
Mercury 1997 Sable Скачать руководство пользователя страница 27

TILT STEERING

Pull the tilt steering
control toward you to
move the steering
wheel up or down.
Hold the control while
adjusting the wheel to
the desired position,
then release the
control.

Never adjust the steering wheel when the
vehicle is moving.

MOON ROOF (IF EQUIPPED)

Press SLIDE to open
and close moon roof.
Press AUTO and
release to open
completely with one
touch.

Press UP or DN on the
TILT control to tilt
moon roof when closed.

Sliding shade

The moon roof has a sliding shade that you can
open or close when the moon roof is closed.

DOME LAMPS AND MAP LAMPS

The front dome lamp is located overhead between
the driver and passenger seats. If the vehicle is
equipped with a moon roof, the dome lamp is
located behind the moon roof.

TILT

UP

LIGHT

LIGHT

AUTO

DN

SLIDE

dno_moonroof

dno_slide-shade

dno_dome-map

Controls and features

27

Содержание 1997 Sable








































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды