manualshive.com logo in svg

Mercury 1997 Sable, Руководство пользователя

Поделиться
Скачать
Mercury 1997 Sable Скачать руководство пользователя страница 140

•

At least ten minutes of driving on an expressway
or highway.

Before completing the above driving modes, the
engine must be warmed up and at operating
temperature. Once started, the vehicle must not be
turned off during these driving modes.

EXTERIOR LAMPS

It is a good idea to check the operation of the
following lights frequently:

•

Headlamps

•

High-mount brake lamp

•

Tail lamps

•

Brake lamps

•

Backup lamps

•

Hazard flashers

•

Turn signals

•

License plate lamp

•

Interior overhead lamps

Do not remove lamp bulbs unless they will be
replaced immediately. If a bulb is removed for an
extended period of time, contaminants may enter
the lamp housings and affect performance.

High-mount brake lamp - Sedan

To remove the brake lamp:

1. Remove package
tray trim, then push
attachment toward the
rear.

2. Slide brake lamp up
and away from the rear
window to remove it
from the tabs that hold
it down.

3. Disconnect bulbs.

dno_drive-cycle

dno_exterior-bulbs

Maintenance and care

140

Содержание 1997 Sable








































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды