manualshive.com logo in svg

Mercury 1997 Sable, Руководство пользователя

Поделиться
Скачать
Mercury 1997 Sable Скачать руководство пользователя страница 118

9. Power steering fluid reservoir

CHECKING AND ADDING ENGINE OIL

Checking the engine oil

Check the engine oil each time you fuel your
vehicle.

To check the oil:

1. Make sure the vehicle is on level ground. If the
engine is warm, turn the engine off and wait a few
minutes for the oil to drain into the oil pan.

2. Set the parking brake and ensure the gearshift is
securely latched in P (Park).

3. Open the hood. Protect yourself from engine heat.

4. Locate and carefully
remove the engine oil
dipstick.

5. Wipe the dipstick clean. Insert the dipstick fully,
then remove it again. The oil level should be in the
range shown on the dipstick.

6. If the oil level is below the MIN line or the ADD 1
QUART line, add oil as necessary. If the oil level is
beyond the MAX or FULL line, engine damage or
high engine oil consumption may occur and some oil
must be removed from the engine by a service
technician.

7. Put the dipstick back in and ensure it is fully
seated.

Adding engine oil

1. Check the engine oil. For instructions, refer to

Checking the engine oil

in this chapter.

ADD 1 QT

FULL

dno_engine-oils

dno_check-oil

dno_add-oil

Maintenance and care

118

Содержание 1997 Sable








































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды