Meler B4 NON-STOP Скачать руководство пользователя страница 33

Страница: 33 / 78

4-5

MELTER OPERATION

MA-5081-E

B4 NS ADHESIVE MELTER MANUAL

Temperature display for each component

The temperature of each component (tank and each hose and applicator) can

be displayed by selecting the component using the cursors.

Press the component selection up/down arrow until the desired component is

displayed.

After 10 seconds the display returns to the default component (tank).

If you would like the component to be displayed permanently press the up-

down button for 2 seconds on the selected component.

The display sequence is as follows:

tank<—hose1<—applicator1<—hose2<—applicator2

tank—>hose1—>applicator1—>hose2—>applicator2

To permanently remove a component from the display, simply press any of the

up-down arrows.

Alarm display

The B4 NS melters inform the user when there is a malfunction in the unit, by

sending messages that can be seen on the control panel display.

When an alarm appears, the control should take a series of actions to

protect the unit. Simply correct the fault and the control will reactivate the

equipment’s functions.

Activating the standby function does not trigger any alarm.

If the sensor is broken, the system will keep all the components hot, except

for the one in which the fault has occurred.

In the event of overheating, the system immediately stops heating the failed

component. If after three minutes, the fault persists, the system will stop

heating all components and the power relays will be disconnected. The panel

will continue to display the alarm until the error has been rectified. Once

resolved, the power relays will be reactivated and the system will begin to heat

as normal.

Code

Cause

Actions

Heating

Pump

Main machine signal

Err 0

tank broken sensor

only tank off

off

Err 1

hose1 broken sensor

only hose1 off

off

Err 2

applicator1 broken sensor

only applicator1 off

off

Err 3

hose2 broken sensor

only hose2 off

off

Err 4

applicator2 broken sensor

only applicator2 off

off

Err 100

tank overheating

all components off

off

Err 101

hose1 overheating

all components off

off

Err 102

applicator1 overheating

all components off

off

Err 103

hose2 overheating

all components off

off

Err 104

applicator2 overheating

all components off

off

E r r

Содержание B4 NON-STOP















































































Результаты поиска

Содержание B4 NON-STOP

Отзывы:

Похожие инструкции для B4 NON-STOP

Бренды по названию

Популярные бренды

Meler B4 NON-STOP, Инструкция по эксплуатации

Результаты поиска

Содержание B4 NON-STOP

Отзывы:

Похожие инструкции для B4 NON-STOP

Бренды по названию

Популярные бренды