Meler B4 NON-STOP Скачать руководство пользователя страница 32

Страница: 32 / 78

FOCKE MELER GLUING SOLUTIONS

4-4

MELTER OPERATION

Melter displays

The control panel on the B4 NS melters have two displays, each with three

sets of 7 segments to display the temperature values (set point and actual

temperature), the programmable parameters and alarms.

They are equipped with LED indicators to display the heating of each

component, as well as the pump activations and the main machine connection

signal:

They are also equipped with LEDs indicating the programming of the

equipment connection/disconnection and the connection/disconnection of the

standby function:

LED display

Component heating

Component status

constantly lit

constant

low temperature

blinking slowly

as need (according to PID parameters) temperature near set point

blinking rapidly

programming or display

change in set point values

off

not heating

temperature reached

LED display

On/off

Standby

constantly lit

turned off unit

function activated

blinking slowly

deactivation programmed for the

current day

activation programmed for the

current day

blinking rapidly

activation/deactivation

programming mode

activation/deactivation

programming mode

off

unit in operation

function deactivated

simultaneous intermittence from leds of

pump activation and main machine signal timing in progress, once the tank has reached its set point temperature

Содержание B4 NON-STOP















































































Результаты поиска

Содержание B4 NON-STOP

Отзывы:

Похожие инструкции для B4 NON-STOP

Бренды по названию

Популярные бренды

Meler B4 NON-STOP, Инструкция по эксплуатации

Результаты поиска

Содержание B4 NON-STOP

Отзывы:

Похожие инструкции для B4 NON-STOP

Бренды по названию

Популярные бренды