Meinberg LANTIME Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 153

background image

SETUP SHS Time Limit

In this menu the maximum time limit is to be configured. If the deviation between

GPS time and PZF time exceeds the configured time limit, the hybridsystem stops
generating time strings. The time limit can be set between 1 ms and 400 ms.

SETUP
SHS max.Diff
act.Diff: < 1ms
max.Diff: 001ms

SETUP LAN PARAMETERS

In this submenu the network parameters are configured. These parameters have to

be adapted to the existing network when the LANTIME is installed the first time. The
following parameters can be set:

TCP/IP ADDRESS, NETMASK, DEFAULT

GATEWAY, IPv6 ADDRESS HOSTNAME, DOMAINNAME, NAMESERVER,
SYSLOG SERVER, SNMP MANAGER, REMOTE CONNECT,

RESET

FACTORY SETTINGS und NET LINK MODE

. All settings are applied to the

first Ethernet interface only. All further Ethernet interfaces have to be configured via
HTTP or CLI interface. With the submenu REMOTE CONNECT you can enable or
disable all network connections via TELNET, FTP or HTTP. When the network
parameters have been changed the configuration file is updated and the NTPD is
restarted.

SETUP
LAN PARAMETERS
TCP/IP ADDRESS

000.000.000.000

SETUP
LAN PARAMETERS
NET MASK

255.255.255.000

With the submenu

RESET FACTORY SETTINGS

the following parameters will

be set to the default values:

SETUP

LAN PARAMETERS

Reset factory

settings

Reset Factory ?

INC -> YES

MENU -> NO

All configuration parameters of the timeserver are saved on the Flash Disk in the file /
mnt/flash/global_configuration. It is recommended not to modify this file manually
but to use the configuration interface (HTTP, CLI or SNMP). If this file does not
exist, an empty file is generated. The default configuration file is part of the
attachment.

The parameters for speed and mode of the net card can be changed with the menu
item NET LINK MODE. There are 5 modes available: Autosensing, 10 MBit/Half-
Duplex, 100 MBit/Half-Duplex, 10 MBit/Full-Duplex, 100 MBit/Full-Duplex.
Default setting is Autosensing.

34

«
...
32
33
34
35
36
...
»

Содержание LANTIME


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LANTIME

Бренд: XDS Страницы: 99

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

Бренд: Fostex Страницы: 20

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: Dantel Страницы: 62

Бренд: Nakayo Страницы: 119

Бренд: Quantum Страницы: 7

AT32F421 Series

Бренд: ARTERY Страницы: 337

Бренд: ZyXEL Communications Страницы: 3

Бренд: JETWAY Страницы: 47

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

Бренд: AMC Страницы: 28

Imagestore Intuition+

Бренд: Miranda Страницы: 60

mPCIE-ADIO16-8F Series

Бренд: Acces I/O products Страницы: 13

Бренд: M86 Security Страницы: 540

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды