Meinberg LANTIME Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 153

background image

Configuration via LC Display

On first installation of LANTIME the network parameters can only be configured

by the front panels push buttons and the LC display. Press MENU until the SETUP
menus appear on the display. The first setup menu are the LAN PARAMETERS.
Pressing   NEXT   further   setup   menus   appear.   Pressing   CLR/ACK   the   LAN
PARAMETERS menu is entered. The submenu TCP/IP ADDRESS appears. Pressing
NEXT   the   following   submenus   can   be   chosen:   NET   MASK,   DEFAULT
GATEWAY, IPv6 address,  HOSTNAME,  DOMAINNAME, NAMESERVER and
REMOTE CONNECT. CLR/ACK lets the user enter the corresponding submenu to
make changes with NEXT and INC. Pressing CLR/ACK after changing parameters
acknowledges the changes. Leaving the menu with MENU all changes are discarded
and   the   setup   menu   is   displayed   again.   All   changed   settings   of   the   LAN
PARAMETER’s sub menu come into affect not before MENU is pressed once again
and the changes are confirmed.

The unique 32 bit TCP/IP address must be set by the network administrator. The net
mask will be defined by the network. It is probable that you will need to set up the
default gateway also.

The correct connection to the LANTIME can be reviewed from any other workstation
in the network with the program PING.

REMOTE CONNECT lets the user enable or disable all connections via network (e.g.
TELNET, FTP or HTTP). If changes occur via HTTP interface or setup program the
message “REMOTE CONNECT: partial enabled” may appear. The NTP protocol will
restart after any change.

NOTE:

Any HTTP, HTTPS, SSH or TELNET connection to the LANTIME is

possible only if REMOTE CONNECT is enabled!

29

«
...
27
28
29
30
31
...
»

Содержание LANTIME


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LANTIME

Бренд: dbx Страницы: 2

Бренд: Alcad Страницы: 6

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

TD-3316B4-16P-A1

Бренд: TVT Digital Страницы: 2

Бренд: Hama Страницы: 25

Бренд: Alcatel-Lucent Страницы: 12

Бренд: Renesas Страницы: 67

Бренд: Roland Страницы: 224

Бренд: A4Tech Страницы: 8

Бренд: Alphacool Страницы: 3

EdgeSafe M40G1AC

Бренд: Garland Страницы: 159

Бренд: Crestron Страницы: 3

RouterBOARD 1000

Бренд: MikroTik Страницы: 9

A2463645 - 2 GB Memory

Бренд: Dell Страницы: 2

4K30-HDMI-CAPTURE

Бренд: StarTech.com Страницы: 2

Бренд: Aaeon Страницы: 93

Бренд: Aaeon Страницы: 69

SMARTSTOR NS4300N

Бренд: Promise Technology Страницы: 186

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды