Megger SMART THUMP ST16 Скачать руководство пользователя страница 30

Страница: 30 / 62

AVTMST16 Rev 1 May 2016

Menu item

Description

Import from
USB

Imports a cable list from an inserted USB drive. The cable list must
be located in the

CableLists

folder.

Export to
USB

Exports the selected cable list to the

CableLists

folder on the USB

drive.

Remove
cable list

Removes the selected cable list from internal memory.

User mode

Menu item to select the

User Mode

which is the default after start-up.

If set to

Last,

the unit starts up in last active mode,

recommended

is to set to

QUICK STEPS

Backlight settings

Backlight timeout and contrast settings

Time Out Settings

Minutes of inactivity after which the system is automatically shut down.

Stored Traces

Menu item to export or delete all traces which have been stored in the internal
memory.

Exporting traces requires a USB flash drive plugged into the USB port

. The

traces are written into the

EtrayTraces

folder which is automatically created.

The data can be viewed in any regular web browser by opening the

index.html

file

which is also located in the

EtrayTaces

folder.

System information

Displays the detailed hardware and software configuration of the unit.

Change password

Menu item to change the password required to enable the

EXPERT MODE

Customize TDR
features

Menu item to configure the options which are available during measurement,

See

page 45.

Return

By leaving the

EXPERT MODE

through this menu item, the new settings are

saved.

Содержание SMART THUMP ST16































































Результаты поиска

Содержание SMART THUMP ST16

Отзывы:

Похожие инструкции для SMART THUMP ST16

Бренды по названию

Популярные бренды

Megger SMART THUMP ST16, Руководство пользователя

Результаты поиска

Содержание SMART THUMP ST16

Отзывы:

Похожие инструкции для SMART THUMP ST16

Бренды по названию

Популярные бренды