Megger SMART THUMP ST16 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 62

background image

M

AVTMST16 Rev 1 May 2016

12

Backup Battery

If the internal battery is becoming drained while fault locating, any 12 V battery
providing more than 50 A (e.g. a car battery) can be connected to the
12 V terminals

in order to extend the operation time or the unit must be

connected to an AC source (see below AC Line Operation).

Charging

The battery automatically is being charged as soon as the SMART THUMP has
been connected to 120/230 AC line power. Charging time on a fully drained
battery is about 10 to 12 hours. The progress of the charging process is indicated
by the battery charging status LED

. During charging, the LED lights yellow.

It turns to green, when the battery is full and charging is finished.

NOTE:

Always charge the battery immediately after use. Lead-acid batteries
must always be kept in a charged condition. The battery life is longer
with an almost fully charged battery rather than fully discharged one.

Store the unit always at a full charge by keeping the charger connected
while the unit is not in use (trickle charge).

AC Line Operation

As soon as the AC power cord is connected to the receptacle

of the SMART

THUMP and the AC line,

the system is operating on AC power and being

charged at the same time.

«
...
20
21
22
23
24
...
»

Содержание SMART THUMP ST16































































Отзывы:

Нет отзывов

Похожие инструкции для SMART THUMP ST16

Бренд: ABB Страницы: 14

Бренд: NEC Страницы: 29

Бренд: vanEE Страницы: 52

Бренд: Caddon Hives Страницы: 3

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Qu-Bit Electronix Страницы: 15

Бренд: Quark-Elec Страницы: 2

Бренд: V.ORLANDI Страницы: 144

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

REBOUND DIABETIC WALKER

Бренд: Össur Страницы: 63

Бренд: Össur Страницы: 67

ECHODIA Babyscreen

Бренд: Électronique du Mazet Страницы: 65

Бренд: SAC Страницы: 2

Бренд: Ebyte Страницы: 7

Бренд: K-SPORT Страницы: 5

Бренд: Ganter Norm Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды