Megger SMART THUMP ST16 Скачать руководство пользователя страница 55

Страница: 55 / 62

Advanced System Settings

AVTMST16 Rev 1 May 2016

How to Setup Customer-Specific TDR Features

Thanks to the high level of configurability of the SMART THUMP, the TDR
features for both, "EXPERT MODE" and "QUICK STEPS MODE", (see page
17) are customer configurable.

In order to create your own customer-specific settings, proceed as follows:

Step Action

Enable the EXPERT MODE. See page 18.

Access the expert settings via the

menu item.

Select the

Customize TDR Features

menu item.

Select the

Setup options

menu item.

If you want to change the options of the QUICK
STEPS mode…

If you want to change the options of
the EXPERT MODE…

… select the

QUICK STEPS

menu item.

… select the

Expert

menu item.

Select the option you want to activate / deactivate. An overview table of all options can
be found in appendix 1.

Select one of the available options by rotating the rotary knob

Disabled

The option is not available in the selected user mode.

Simple

The option is available in the

Standard Options

menu of the selected

user mode.

Extended

The option is available in the

Extended Options

menu of the selected

user mode.

Confirm the selection with

If required, perform steps

for further options.

The adjusted configuration can be shared among your units using the

Export

and

Import

functions of the

Menu Locate Options

menu.

Содержание SMART THUMP ST16































































Результаты поиска

Содержание SMART THUMP ST16

Отзывы:

Похожие инструкции для SMART THUMP ST16

Бренды по названию

Популярные бренды

Megger SMART THUMP ST16, Руководство пользователя

Результаты поиска

Содержание SMART THUMP ST16

Отзывы:

Похожие инструкции для SMART THUMP ST16

Бренды по названию

Популярные бренды