Megger SMART THUMP ST16 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 62

background image

M

AVTMST16 Rev 1 May 2016

24

How to Verify Whether it is Actually a Bad Section

The HIPOT test within the context of Sectionalizing is done to confirm, that the
section of cable identified as bad during the Sectionalizing procedure can be
verified to be actually bad. Proceed as follows to perform a HIPOT test

after the

identified cable section has been isolated at the 2 closest transformers

:

Step Description

1

Select the

menu item from the main menu or from the

submenu (depends on the

system configuration).

2

Adjust the test voltage and select

to confirm the value.

3

Press the green illuminated “HV ON” button

.

4

Select

to start the test (only if

measurement start

option is set to

manual. See

“System Settings” on page 17).

Result:

The selected voltage is applied to the cable.

During the rise of the voltage the maximum current of the HVPS will be displayed till the
cable has been fully charged, at which time the current will drop down to the actual
leakage current level. The insulation resistance is displayed. This scenario is observed if
the cable has no insulation breakdown, otherwise the high voltage will be shut off when
the flashover/breakdown occurs.

Depending on whether or not a breakdown takes place during the test, one of the
following results is presented in the display:

Breakdown
at…kV

A voltage breakdown took place at the indicted test voltage.

No Flash-
over

The cable has successfully withstood the applied DC test voltage. If

possible, repeat (

) the test with higher voltage (do not exceed the

maximum permissible voltage).

Cable not
chargeable

The cable could not be charged by the test voltage. This is typically due to
a short (fault) in the cable.

Low
resistance
at …kV

The HV source cannot charge the cable beyond the indicated voltage value
due to the very high leakage current level.

5

Select

to return to the main menu.

«
...
32
33
34
35
36
...
»

Содержание SMART THUMP ST16































































Отзывы:

Нет отзывов

Похожие инструкции для SMART THUMP ST16

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: Makerfire Страницы: 10

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: Yardline Страницы: 75

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: IDEAL Страницы: 12

Бренд: IEMCA Страницы: 82

KID 80-IV Touch

Бренд: IEMCA Страницы: 122

Бренд: Calrec Страницы: 92

Бренд: Labnet Страницы: 12

Accublock D1301

Бренд: Labnet Страницы: 13

Бренд: LANGER EMV-Technik Страницы: 25

Electric Clamshell CSE12-208VCD

Бренд: Lang Страницы: 16

Brillion 3631-25

Бренд: Landoll Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды