mectron Multipiezo Скачать руководство пользователя страница 9

Страница: 9 / 76

INTRODuCTION

•

use of non original MECTRON inserts

used in accordance with the settings

designed and tested on the original

MECTRON inserts. Correct use of the

settings is only guaranteed with original

MECTRON inserts;

•

Shortage of stock material (handpiece,

inserts, wrenches) to be used in case of a

standstill due to faults or problems;

•

Incorrect/omitted maintenance

compared to what is stated in

Chapter 9

on page 50

of this manual;

• Breach of the requirements and the

information contained in

Chapter 5.5 on

page 24

of this manual;

• Breach of the requirements and the

information contained in

Chapter 8 on

page 31

of this manual;

• Unauthorised repairs in accordance with

the indications contained in

Chapter 12.4

on page 66

this manual.

1.4

Safety Requirements

WARNING

Contraindications.

Do not use the multipiezo on patients who

carry heart stimulators (Pace-makers) or

other implantable electronic devices. This

precaution also applies to the operator.

WARNING

Contraindications.

Do not

perform scaling treatments without water

spray in order to avoid the insert over-

heating which may cause damages to the

tooth. Treatments with no water spray can be

carried out only with “Dry Work” inserts which

do not have the water passage.

CAUTION

Contraindications. Ultrasonic

scaler.

Do not perform treatments on metal

or ceramic/porcelain prosthetic artifacts

(unless otherwise specified). The ultrasonic

vibration could cause decementation/

loosening of such artifacts.

WARNING

Contraindications.

Interference from other equipment.

An electrosurgical scalpel or other

electrosurgical units positioned near the

multipiezo device may interfere with its

correct operation.

WARNING

Contraindications.

Interference with other equipment.

Even if compliant with standard IEC 60601-

1-2, multipiezo may interfere with other

devices in the vicinity. The user should take

whatever steps are necessary to eliminate

or reduce the source of interference. Install

the Multipiezo at safety distance from life-

support systems. multipiezo must not be

used adjacent or stacked with other electrical

equipments. If adjacent or stacked use of

the device is necessary, normal operation

of the equipment and multipiezo, in the

configuration in which they will be used,

should be verified prior their use.

WARNING

Risk of explosion.

The

device cannot operate in environments where

the atmosphere is saturated with flammable

gases (aesthetic mixtures, oxygen, etc.).

Содержание Multipiezo












































































Результаты поиска

Содержание Multipiezo

Отзывы:

mectron Multipiezo, Руководство по эксплуатации и обслуживанию, Страница: 9 / 76

Результаты поиска

Содержание Multipiezo

Отзывы: