mectron Multipiezo Скачать руководство пользователя страница 66

Страница: 66 / 76

multipiezo

11.1.4

Specifications of the Tests for the Immunity of the Accessible

Parts of the Casing to the Wireless RF Communications Device

multipiezo is designed to operate in an electromagnetic environment in which radiated RF

disturbances are under control. The purchaser or operator of multipiezo can help prevent

electromagnetic interferences by guaranteeing a minimum distance between the mobile and

portable RF communication devices (transmitters) and multipiezo, as recommended below, in

relation to the maximum output power of the radio communication devices.

Test

Freq.

(MHz)

Band

(MHz)

Service

Modulation

Max

power

(W)

Distance

(m)

Immunity

test value

(V/m)

385

380 - 390

TETRA 400

Pulse

modulation

18 Hz

1.8

0.3

450

430 - 470

GMRS 460

FRS 460

± 5 kHz

deviation

1 kHz sine

0.3

710

704 - 787

LTE band 13,

Pulse

modulation

217 Hz

0.2

0.3

745
780
810

800 - 960

GSM 800/900

TETRA 800

iDEN 820

CDMA 850

Band LTE 5

Pulse

modulation

18 Hz

0.3

870

930

1720

1700 - 1990

GSM 1800

CDMA 1900

GSM 1900

DECT

LTE Band 1, 3,

4, 25

uMTS

Pulse

modulation

217 Hz

0.3

1845

1970

2450

2400 - 2750

Bluetooth

WLAN

802.11 b/g/n

RFID 2450

Band LTE 7

Pulse

modulation

217 Hz

0.3

5420

5100 - 5800

WLAN

802.11 a/n

Pulse

modulation

217 Hz

0.2

0.3

5500

5785

a) For some services, only uplink frequencies are

included.

b) The carrier must be modulated using a square wave

signal with a duty cycle of 50%.

c) As an alternative to FM modulation, 18 Hz pulse

modulation at 50% can be used because, although it

does not represent true modulation, it represents the

worst case.

Содержание Multipiezo












































































Результаты поиска

Содержание Multipiezo

Отзывы:

mectron Multipiezo, Руководство по эксплуатации и обслуживанию, Страница: 66 / 76

Результаты поиска

Содержание Multipiezo

Отзывы: