mectron Multipiezo Скачать руководство пользователя страница 60

Страница: 60 / 76

multipiezo

11.1

Electromagnetic Compatibility IEC/EN 60601-1-2

WARNING:

Contraindications.

Interference with other equipment

Even if compliant with standard IEC/EN

60601-1-2, multipiezo may interfere with

other devices in the vicinity. multipiezo

must not be used near or stacked with

other devices. Install multipiezo far from

subsistence equipment. However, if this

is necessary, the correct operation of the

equipment in that configuration, and of all

equipment, must be checked and monitored

before starting the intervention.

WARNING:

Portable and mobile radio

communication equipment may influence the

correct operation of the device.

WARNING:

Contraindications.

Interference from other equipment

An electrosurgical scalpel or other

electrosurgical units positioned near the

multipiezo device may interfere with the

correct operation of the device itself.

WARNING:

The device requires particular

EMC precautions and must be installed

and put into service according to the EMC

information provided in this chapter.

WARNING:

Only use original Mectron

accessories and spare parts. The use of

cables and accessories not supplied by

Mectron might negatively affect the EMC

performances.

11.1.1

Guide and Manufacturer’s Declaration - Electromagnetic

Emissions

multipiezo is designed to operate in the electromagnetic environment specified below. The

purchaser or user of multipiezo should ensure that it is used in such an environment.

Emissions Test

Compliance

Electromagnetic Environment Guidance

RF Emissions

CISPR 11

Group 1

multipiezo uses RF energy only for its internal

operation. Therefore, its RF emissions are

very low and probably do not cause any

interference with nearby electronic devices.

RF Emissions

CISPR 11

Class B

multipiezo is suitable for use in all buildings,

including domestic buildings, and those

directly connected to the public low-

voltage power supply network that supplies

buildings used for domestic purposes.

Harmonic emissions

IEC 61000-3-2

Class A

Emissions of fluctuations

voltage/flicker

IEC 61000-3-3

Compliant

Содержание Multipiezo












































































Результаты поиска

Содержание Multipiezo

Отзывы:

mectron Multipiezo, Руководство по эксплуатации и обслуживанию, Страница: 60 / 76

Результаты поиска

Содержание Multipiezo

Отзывы: