mectron Multipiezo Скачать руководство пользователя страница 18

Страница: 18 / 76

multipiezo

WARNING

Risk of explosion.

The device cannot operate in environments

where there are saturated atmospheres of

flammable gases (aesthetic mixtures, oxygen,

etc.).

WARNING

: Install the device in a safe

place protected against impacts or accidental

splashes of water or other liquids.

WARNING

: Do not install the device

above or near heat sources. Foresee

adequate air circulation around the device

when installing it.

CAUTION

: Do not expose the device to

direct sunlight or to sources of UV light.

CAUTION

: The device can be transported

but must be handled with care when moved.

Position the pedal on the floor so that it

can only be activated intentionally by the

operator.

CAUTION

: Before connecting the

handpiece to its cord, check that the electrical

contacts are perfectly dry, on both sides. If

necessary dry them with compressed air.

CAUTION

: Each tank can hold liquids up

to a maximum of 500 ml.

CAUTION

: Always position the device

in way so that the power switch is easily

reachable, since this switch is considered as a

load-break switch.

4.3 Connecting the Accessories

Connect the pedal to the back of the

device, on the right-hand side, in the

socket marked with the symbol

inserting the pedal cord plug until you

hear a ‘click’.

WARNING

Pay attention to the

positioning of the pedal, which must be

positioned on the floor so that it can

only be activated intentionally by the

operator.

Plug the power supply cord into the

power socket on the back of the device’s

console.

Plug the other end of the power cord into

a hospital-grade wall outlet;

Содержание Multipiezo












































































Результаты поиска

Содержание Multipiezo

Отзывы:

mectron Multipiezo, Руководство по эксплуатации и обслуживанию, Страница: 18 / 76

Результаты поиска

Содержание Multipiezo

Отзывы: