mectron Multipiezo Скачать руководство пользователя страница 42

Страница: 42 / 76

multipiezo

8.4 Cleaning the Sterilisable Accessories

NOTE:

The cleaning procedures must be

performed immediately after each use.

Immerse the insert and/or instrument in

demineralised water or in an enzymatic

detergent solution immediately after use.

Do not leave residue or blood deposits on

the inserts and instruments, eliminate larger

impurities with a disposable cloth or paper

towel.

The sterilisable parts of the device are:

•  Scaler handpiece;
•  Scaler nose cone;
•  Scaler light pipe;
•  Inserts;
•  Inserts torque wrench.

CAUTION

: The instructions supplied

below have been validated by the

manufacturer of the medical device as ABLE

to prepare a medical device for re-use.

The process manager is responsible for

ensuring that the processes repeated are

effectively performed using the equipment,

materials and staff in the reprocessing

structure in order to obtain the desired

result. This generally requires the validation

and systematic monitoring of the process.

Similarly, all deviations from the instructions

provided by the processes manager must be

adequately assessed to judge their efficiency

and potential undesired consequences.

8.4.1 Manual Cleaning

8.4.1.1 Required Materials

•

Enzymatic detergent at pH 6-9;

•

Water;

• Container for immersion in the

enzymatic liquid;

•

ultrasonic tank;

•

Clean, soft, low-lint cloths;

•  Brush with soft nylon bristles;
•  Syringe;
•  Demineralised water.

CAUTION

: To disinfect the device and/

or its accessories, it is recommended the use

of water-based disinfectant solutions with

aneutral pH (pH7).

DO NOT USE

as disinfectants:

•

Alcohol-based disinfectant solutions;

•

Peracetic acid, Formaldehyde,

• Gluteraldehyde based products or other

equivalent solutions/products;

•

very alkaline products (pH > 9);

•

Products containing sodium

hypochlorite;

•

Products containing hydrogen peroxide;

•

Products containing abrasive substances;

•

very acid products (PH < 4);

•

Products containing aldehyde, amine

and/or phenols;

• Acetone;
•

Methylethylketone;

since they may discolour and/or damage the

plastic materials.

The manufacturer disclaims all liability for any

damage caused by the substances mentioned

above. In case of damage caused by those

substances, the Warranty will be void.

Содержание Multipiezo












































































Результаты поиска

Содержание Multipiezo

Отзывы:

mectron Multipiezo, Руководство по эксплуатации и обслуживанию, Страница: 42 / 76

Результаты поиска

Содержание Multipiezo

Отзывы: