mectron Multipiezo Скачать руководство пользователя страница 8

Страница: 8 / 76

multipiezo

WARNING

: The device must be used

in a dental practice, in a clinic, or in a

professional oral hygiene and preventive

care centres. Do not use the device in

environments where the atmosphere

is saturated with flammable gases

(anaesthetic mixtures, oxygen, etc.).

WARNING

Qualified and specialised

personnel

The device is intended exclusively for use by

a dentist, or dental hygienist, with suitable

medical/health training. The use of the

device does not cause side effects if it is

used correctly. An improper use might cause

tissues heating.

WARNING

Intended use.

Use the device

exclusively for the use for which it is intended.

Failure to observe this regulation can cause

serious injury to the patient, the operator,

and damages/breakdowns to the device.

1.2

Description of the Device

multipiezo is a multifunctional ultrasonic

piezoelectric scaler. It has been designed

in order to offer a product with innovative

design and exclusive technical characteristics

to the operator, and maximum comfort during

the treatment to the patient.

The user interface has been optimized making

all the functions readily available by integrating

them in the touch keyboard. The handpiece

has a circular LED light and can be autoclaved

at 135 °C. The device has an automatic sync

circuit which optimizes frequency and power

for each available insert, so that the best

performance is always assured.

1.3

Disclaimer

The manufacturer MECTRON disclaims any

liability, expressed or implied, and shall have

no responsibility for any direct or indirect

personal injury and/or property damage,

occurring as a result of incorrect procedures

in the use of the device and its accessories.

The manufacturer MECTRON shall be under

no liability, expressed or implied, for any type

of personal injury and/or property damage,

which might arise or be caused, whether by

the customer or by any of the users of the

product and its accessories, as results of the

following conditions, by way of example and

not limitated to:

• Misuse or use during procedures other

than those specified in the intended use

of the product;

•

The environmental conditions for

preservation and storage of the device

are not complying with the requirements

indicated in

Chapter 11 on page 52

;

•

The device is not used in compliance

with all the instructions and precautions

described in this manual;

•

The electrical system in the premises in

which the device is used is not compliant

with the applicable regulations and with

the electrical safety requirements;

•

Assembly operations, extensions, re-

adjustments, upgrades and repairs of the

device are carried out by personnel not

authorised by Piezosurgery Inc.;

• Misuse, abuse, abnormal use, negligent

use, intentional misconduct or use

exceeding the limits of the device

indicated and allowed and/or normal

wear or deterioration, ill-treatment and/

or incorrect interventions;

• Any attempt to tamper with or

modification of the device under any

circumstance;

•

use of non original MECTRON inserts

resulting in permanent damage to the

thread of the handpiece with impaired

functioning and risk of injury to the

patient;

Содержание Multipiezo












































































Результаты поиска

Содержание Multipiezo

Отзывы:

mectron Multipiezo, Руководство по эксплуатации и обслуживанию, Страница: 8 / 76

Результаты поиска

Содержание Multipiezo

Отзывы: