McFarlane WDL-2000 Скачать руководство пользователя страница 7

Страница: 7 / 58

How to Install Safety Signs:



Be sure that the installation area is clean and dry.



Decide on the exact position before you remove the backing paper.

Tire Safety



Failure to follow proper procedures when mounting a tire on a wheel or rim can produce an

explosion which may result in serious injury or death.



Do not attempt to mount tires unless you have the proper equipment and experience to do the job.



Inflating or servicing tires can be dangerous. Whenever possible, trained personnel should be

called to service and/or mount tires.



Always order and install tires and wheels with appropriate capacity to meet or exceed the weight

of the unit. Be sure to inflate tires to tire manufacturer’s specifications



Tires that are provided by the manufacturer are designed for speeds LESS THAN 20mph. Do

Not exceed or tire failure will occur.

Remember

Your best assurance against accidents is a careful and responsible operator. If there is any
portion of this manual or function you do not understand, contact your local authorized dealer
or the manufacturer.

Before Operation:



Carefully study and understand this manual.



Do not wear loose fitting clothing which may catch in moving parts.



Always wear protective clothing and substantial shoes.



It is recommended that suitable protective hearing and (eye protection) sight protectors be worn.



Keep wheel lug nuts or bolts tightened.



Assure that the tires are inflated evenly.



Give the unit a visual inspection for any loose bolts, worn parts, or cracked welds, and make

necessary repairs. Follow the maintenance safety instructions included in this manual.



Before using the hydraulics on the cart, be sure all fittings and connections are tight.



Be sure that there are no tools lying on the unit.



Make sure that the area is clear of children, animals, and other obstacles before using.



Don’t hurry the learning process or take the unit for granted. Ease into it and become familiar

with your new equipment. Practice operation of your new unit. Completely familiarize yourself

and other operators with its operation before using.

Содержание WDL-2000



























































Результаты поиска

Содержание WDL-2000

Отзывы:

Бренды по названию

Популярные бренды

McFarlane WDL-2000, Руководство оператора и инструкции по настройке

Результаты поиска

Содержание WDL-2000

Отзывы:

Бренды по названию

Популярные бренды