manualshive.com logo in svg

McFarlane WDL-2000, Руководство оператора и инструкции по настройке

Поделиться
Скачать
McFarlane WDL-2000 Скачать руководство пользователя страница 32

 

32 

 

Complete the following steps on each side of the cart.  Refer to Figure 29. 

 

1.

 

Loosen the eye bolt and detach the tension spring from the lock arm. 

2.

 

Rotate the pivot arm and the lock arm so that they are fully engaged. 

3.

 

Reattach the spring and tighten the eye bolt to put tension on the spring. 

4.

 

Move the lock arm mounting bracket forward or back on the A-frame to ensure that the pivot arm 

and lock are fully engaged. 

5.

 

Clamp the lock arm assembly in place by tightening the bolts.  Check to make sure that the pivot 

arm and the lock arm are still fully engaged. 

6.

 

Attach the ¾” x 6” yoke to the tab on the lock bracket.  Thread the adjuster rod into the clevis 

until the bushing on the other end of the rod lines up with the two tabs on the A-frame.  Secure 

into place using the 1” x 2 ½” clevis pins and cotter pins. 

PIVOT ARM

1 X 2 1/2 CLEVIS PIN

& COTTER PIN

& LOCK ARM

EYE BOLT, SPRING AND

CHAIN ASSEMBLY

3/4 X 2 1/2 BOLT

3/4" CLEVIS

ADJUSTER ROD

& LOCK NUT

 

Figure 29 

 

Attach the Cable Brackets 

 

1.

 

Attach the cable bracket to the center bar 6” from the cylinder hinge plate.  Refer to Figure 30.  

Use two 1/2 x 6 x 7 1/4 U-bolts (1/2 x 7 x 8 1/4 for 2070 and 2080 models), lock washers and 

hex nuts. 

2.

 

Repeat on the other side of the cart. 

Содержание WDL-2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды