manualshive.com logo in svg

McFarlane WDL-2000, Руководство оператора и инструкции по настройке

Поделиться
Скачать
McFarlane WDL-2000 Скачать руководство пользователя страница 24

 

24 

Connect a 12 or 16-Bar Section

 

 

1.

 

Bolt the pull chains to the front tabs on the front harrow sections.  Refer to Figure 16.  Use 1/2” x 

1 1/2” bolts, flat washers, lock washers, and hex nuts.  The chains should be bolted to the bottom 

of the pull tabs. 

2.

 

Bolt the front and rear harrow sections together using two 5/16” x 1 1/2” x 6” dual section 

connector links at each pull tab.  Refer to Figure 18.  Use two 1/2” x 2” bolts, lock washers, and 

hex nuts.  Do 

not 

tighten yet. 

3.

 

Bolt the lift chains to the dual section connector links.  Use one 7/16” V-bolt and two lock nuts 

on each link.  Tighten all dual section connector link bolts. 

4.

 

Make sure that the harrow sections match each other, the angle of attack is correct, and the chains 

are not twisted. 

DUAL SECTION

CONNECTOR LINKS

7/16" V-BOLT

1/2" x 2" BOLTS

LIFT ARM

FRONT

SECTION

REAR

SECTION

 

Figure 18 

 

 

Connect Dual Sections 

 

1.

 

Bolt the pull chains to the front tabs on the harrow sections.  Refer to Figures 16 and 19.  Use 

1/2” x 1 1/2” bolts, flat washers, lock washers, and hex nuts.  The chains should be bolted to the 

bottom of the pull tabs. 

2.

 

Bolt the lift chains to the bottom of the rear lift tabs of the front harrow sections.  Refer to Figure 

19.  Use 1/2” x 1 1/2” bolts, flat washers, lock washers, and hex nuts. 

3.

 

Make sure that the harrow sections match each other, the angle of attack is correct, and the chains 

are not twisted. 

 

Содержание WDL-2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды