manualshive.com logo in svg

McFarlane WDL-2000, Руководство оператора и инструкции по настройке

Поделиться
Скачать
McFarlane WDL-2000 Скачать руководство пользователя страница 26

 

26 

Attach the Transport Wheels 

 

1.

 

Attach the transport wheel axle assemblies to the wings between the 2

nd

 and 3

rd

 lift arms 

(counting from the field position wing wheel end of the wings).  Use 3/4” x 8 1/2” bolts (3/4” x 

10” for 2070 and 2080 models), lock washers, and hex nuts.  Be sure to mount it 10” from the 

flat edge of the hydraulic transport cylinder post as shown in Figure 21.  Note that there are right 

and left hand transport axle assemblies.  When the spindle is orientated in the vertical direction 

(field position) as shown in Figure 20, the spindle plate should be in contact with the front stop 

block. 

 

Figure 21 

 

2.

 

Attach the hydraulic cylinders with the open ports facing down as shown. Refer to Figure 22.  

Connect the rod end of the cylinder to the transport wing wheel axle and the base end of the 

cylinder to the fixed cylinder post.  Note: When the cylinder is fully retracted the transport wing 

wheel should be in line with all other transport wheels so that the unit can be pulled straight. 

3.

 

Mount the wheels with 11L x 15 tires on the hubs. 

Содержание WDL-2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды