McFarlane WDL-2000 Скачать руководство пользователя страница 44

Страница: 44 / 58

APPENDIX B

FH-816

#4 HARROW BAR (FH-800-8)

FH-820

#4 HARROW BAR (FH-900-8)

FH-803

#5 HARROW BAR (FH-500-8)

FH-807

#5 HARROW BAR (FH-600-8)

FH-811

#5 HARROW BAR (FH-700-8)

FH-815

#5 HARROW BAR (FH-800-8)

FH-819

#5 HARROW BAR (FH-900-8)

FH-803

#6 HARROW BAR (FH-500-8)

FH-807

#6 HARROW BAR (FH-600-8)

FH-811

#6 HARROW BAR (FH-700-8)

FH-815

#6 HARROW BAR (FH-800-8)

FH-819

#6 HARROW BAR (FH-900-8)

FH-801

#7 HARROW BAR (FH-500-8)

FH-805

#7 HARROW BAR (FH-600-8)

FH-809

#7 HARROW BAR (FH-700-8)

FH-813

#7 HARROW BAR (FH-800-8)

FH-817

#7 HARROW BAR (FH-900-8)

FH-804

#8 HARROW BAR (FH-500-8)

FH-808

#8 HARROW BAR (FH-600-8)

FH-812

#8 HARROW BAR (FH-700-8)

FH-816

#8 HARROW BAR (FH-800-8)

FH-820

#8 HARROW BAR (FH-900-8)

E-611

1/2” x 3” SHANK SPIKE TOOTH ONLY

FH-125

CONNECTOR LINK (REGULAR)

FH-127

NOTCHED LINK CAP

1/2” LOCK NUT

FH-122

PULL FLAT

FH-019

CAP CLIP

1/2” x 3” BOLT

1/2” FLANGED LOCK NUT

E-630

SPIKE TOOTH WASHER

E-620

1/2” x 2 1/2” SHANK SPIKE TOOTH ONLY

E-610

1/2” x 2 1/2” SHANK SPIKE TOOTH w/WASHER

HDL-5100

DUAL SECTION CONNECTOR FLAT (16 BAR ONLY)

BV-7611

7/16” V-BOLT (16 BAR ONLY)

1/2” x 2” BOLT, LOCK WASHER AND NUT (16 BAR ONLY)

HDL-5101

DUAL SECTION CONNECTOR ASSEMBLY (16 BAR ONLY)

The #1 bar is the bar with an equal amount of tube to the right and left of the pull flats. The #8 bar is

the bar that is staggered off to one side.

When pulling the harrow section from the #1 bar, the teeth will be in the least aggressive setting.

When pulling from the #8 bar the teeth will be in the most aggressive setting.

9/24/08

Содержание WDL-2000



























































Результаты поиска

Содержание WDL-2000

Отзывы:

Бренды по названию

Популярные бренды

McFarlane WDL-2000, Руководство оператора и инструкции по настройке

Результаты поиска

Содержание WDL-2000

Отзывы:

Бренды по названию

Популярные бренды