manualshive.com logo in svg

McFarlane WDL-2000, Руководство оператора и инструкции по настройке

Поделиться
Скачать
McFarlane WDL-2000 Скачать руководство пользователя страница 50

 

 

APPENDIX B 

50 

AUTO-BACKUP WING PULL-TUBE 

PARTS LIST

 

Always order by Part Number - 

Not

 by Key Number 

KEY  PART # 

DESCRIPTION 

QTY. 

1 

WD-2912 

LOCK BRACKET ASSEMBLY CLAMP PLATE 

2 

2 

WD-2920  

LEFT LOCK BRACKET ASSEMBLY 

1 

** 

WD-2921 

RIGHT LOCK BRACKET ASSEMBLY 

1 

3 

WD-2922 

LOCK ARM 

2 

4 

WD-2901 

PIVOT ARM ASSEMBLY 

2 

** 

WD-2925 

PIVOT ARM ASSEMBLY, 14L TIRES 

2 

5 

WD-2904  

PIVOT ARM BASE 

2 

6 

WD-2914 

PIVOT ARM BASE CLAMP PLATE 

2 

7 

WD-2924 

AXLE CABLE GUIDE BRACKET 

4 

8 

BU-1267 

U-BOLT, 1/2 X 6 X 7 3/4 (2040-2060) 

2 

** 

BU-1278 

U-BOLT, 1/2 X 7 X 8 3/4 (2070-2080) 

2 

9 

WD-2909 

CABLE BRACKET (2040-2060)  

2 

** 

WD-2929 

CABLE BRACKET (2070-2080) 

2 

10 

HD-1216 

BUSHING 

2 

11 

HDL-2534 

EYE BOLT 

2 

12 

RBH-0308 

SPRING 

2 

13 

CH-0703 

3-LINK CHAIN 

2 

14 

AL-030 

SHACKLE 

4 

15 

WD-2911 

LOCK COLLAR 

2 

16 

WD-2915 

TUBE CONNECTOR PIN 

2 

17 

WD-2905 

WING PULL TUBE CONNECTOR 

2 

18 

CH-0607 

7-LINK CHAIN 

2 

19 

WD-181 

QUICK LINK 

2 

20 

WD-2908 

FRAME CABLE GUIDE RING 

2 

21 

WC-8105 

CABLE 

2 

22 

WD-2903 

MAIN PULL TUBE (2040) 

2 

** 

WD-2923 

MAIN PULL TUBE (2050) 

2 

** 

WD-2943 

MAIN PULL TUBE (2060) 

2 

** 

WD-2963 

MAIN PULL TUBE (2070) 

2 

** 

WD-2983 

MAIN PULL TUBE (2080) 

2 

23 

WD-2926 

WING ANCHOR LONG BUSHING 

2 

24 

WD-2906 

WING ANCHOR (2040-2060) 

2 

** 

WD-2946 

WING ANCHOR (2070-2080) 

2 

25 

WDL-2711  WING ANCHOR CLAMP PLATE (2040-2060) 

2 

** 

WDL-2731  WING ANCHOR CLAMP PLATE (2070-2080) 

2 

26 

WD-2916 

WING ANCHOR PIN 

2 

27 

WD-2936 

WING ANCHOR SHORT BUSHING 

2 

28 

WD-2918 

3/4 X 6 YOKE 

2 

29 

HD-1149 

1 X 2 1/2 CLEVIS PIN & 3/16 X 2 COTTER PIN 

2 

30 

WD-2917 

ADJUSTER ROD 

2 

 ** 

Unnumbered items are not pictured. 

 

 *** 

Please specify model number when ordering these parts. 

 

McFarlane Manufacturing reserves the right to change specifications of design at any time 
without obligation to modify previous products.

 

Содержание WDL-2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды