manualshive.com logo in svg

McFarlane WDL-2000, Руководство оператора и инструкции по настройке

Поделиться
Скачать
McFarlane WDL-2000 Скачать руководство пользователя страница 37

 

37 

harness from becoming entangled.  Also, securely attach the wire harness to the lift arm and next 

to the light assembly.  

 

8.

 

Tighten the light assemblies to the lift arms. 

 

9.

 

Check to make sure that all the plugs are properly and securely connected and the wire harnesses 

will not become entangled during operation or when the unit is folded into transport position. 

 

10.

 

Attach the unit to a tractor and plug in the lights. Check to make sure that they are working 

properly and that the wires do not pull or get caught when folding the unit into the transport 

position.  With the unit in transport position, the red and yellow lights should be visible from the 

rear.  The red light should be closest to the ground. 

 

 

 

 

Final Adjustments 

 
1.

 

Check to make sure that all bolts and fasteners are tight. 

2.

 

With the unit in the transport position (refer to the operating instructions), attach the red and 

amber reflectors at the widest visible points.  The red reflectors should be visible from the rear 

of the unit, and the amber reflectors should be visible from the front of the unit. 

Do not detach the unit from the tractor unless the unit is in the transport position with jack stands 

down and the cylinder lock bars in place. 

 

This completes the assembly of your harrow and transport cart.  Before using the unit, double check 

that all components have been assembled properly.  If there are any questions regarding any of the 

assembly steps, contact your local dealer for an explanation.  Do not operate this or any equipment 

unless you are sure that all components operate as they were designed to operate. 

 

Содержание WDL-2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды