McFarlane WDL-2000 Скачать руководство пользователя страница 42

Страница: 42 / 58

APPENDIX B

WDL-2555 TRANSPORT AXLE, LEFT, 2070-2080

WDL-2513 TRANSPORT AXLE CLAMP PLATE, 2040-2060

WDL-2517 TRANSPORT AXLE CLAMP PLATE, 2070-2080

10753 TRANSPORT AXLE SPINDLE, 2040-2060

10754

TRANSPORT AXLE SPINDLE, 2070-2080

WDL-2523 TRANSPORT AXLE THRUST BEARING 2”

WDL-2581 TRANSPORT AXLE WASHER

WDL-2719 WING JACK PLATE, 2040-2060

WDL-2739 WING JACK PLATE, 2070-2080

BU-5867

U-BOLT, 5/8" x 6" x 7 1/" (2040-2060)

BU-5879

U-BOLT, 5/8” x 7” x 8 1/4” (2070-2080)

BU-1267

U-BOLT, 1/2” x 6” x 7 1/4” (2040-2060)

BU-1268

U-BOLT, 1/2” x 7” x 8 1/4” (2070-2080)

WDL-2716 KNUCKLE HINGE PIN, 1 3/4” X 10 1/16” (2040-2060)

WDL-2736 KNUCKLE HINGE PIN, 1 3/4” x 11 1/16” (2070-2080)

WDL-2709 HINGE KNUCKLE, 2040-2060

WDL-2733 HINGE KNUCKLE, 2070-2080

WDL-2302 CENTER BAR ASSEMBLY, 2040-2060

WDL-2312 CENTER BAR ASSEMBLY, 2070-2080

CH-0808

8-LINK PULL CHAIN

CH-0810

10-LINK PULL CHAIN

WDL-2620 8-BAR LIFT ARM, 2040-2060

WDL-2621 8-BAR LIFT ARM, 2070-2080

HDL-2535 4-BAR LIFT ARM, 2040-2060

WDL-2622 4-BAR LIFT ARM, 2070-2080

CH-0808

8-LINK LIFT CHAIN

HD-3xxx

LIFT ARM STABILIZER ANGLES

HDL-3300 REAR PULL POINT ASSEMBLY

SC-600

CYLINDER LOCK BAR

WDL-2714 CENTER BAR HINGE PIN (1 1/2 X 11 1/16)

DC-111

DECAL: "STAND CLEAR..."

DC-116

DECAL: "DO NOT CLIMB ON..."

DC-117

DECAL: "...USE JACK STAND"

DC-119

DECAL: "ESCAPING FLUID..."

Quantity depends on harrow sections used.

Unnumbered items are not pictured.

***

Please specify model number when ordering these parts.

xxx

length in inches (84" is 084, 112" is 112)

McFarlane Manufacturing reserves the right to change specifications of design at any time
without obligation to modify previous products.

Содержание WDL-2000



























































Результаты поиска

Содержание WDL-2000

Отзывы:

Бренды по названию

Популярные бренды

McFarlane WDL-2000, Руководство оператора и инструкции по настройке

Результаты поиска

Содержание WDL-2000

Отзывы:

Бренды по названию

Популярные бренды