Matrix simado gfx11 Скачать руководство пользователя страница 22

Страница: 22 / 88

Matrix SIMADO GFX11 System Manual

•

LED labeled as

RDY

will start blinking (RED) slowly (1 sec On- 1 sec Off) till successful network

registration. After that, it will glow RED continuously.

•

LED labeled as

RDY

will blink (RED) fast (100 ms On- 100 ms Off) when SIM Card is absent or

deactivated or SIM PIN is faulty or SIM PUK is required.

LED Indication during Normal Functioning

Test Calls

Making a Call

•

Lift the receiver of the telephone connected to the FXS Port of SIMADO GFX11/GFX11E. You will get the
dial tone.

•

Dial the desired number. You will hear the Ring Back Tone.

•

Talk when the called party answers the call.

•

Replace the receiver to disconnect the call.

Receiving a Call

•

Ask someone to dial the number of the SIM Card inserted in the Mobile Port of SIMADO GFX11/GFX11E.

•

When the telephone connected to the FXS Port of SIMADO GFX11/GFX11E rings, lift the receiver to talk.

•

You will be in speech with the caller.

•

Replace the receiver to disconnect the call.

SIMADO GFX11/GFX11E is supplied with factory default settings. You can use the system with these settings or
configure it according to your requirement. See

“Configuring SIMADO GFX11/GFX11E”

for instructions.

LED

Activity

Indication

PWR

SIMADO GFX11 is power On.

Off

SIMADO GFX11 is power Off.

RDY

SIM Card is present and active.

Off

SIMADO GFX11 is powered On but SIM Card is not detected.

Blinking

Fast

SIM Card is absent or de-activated or SIM PIN is faulty or SIM PUK is required.

Slow

SIM Card is detected but is not registered with the network.

(controlled

by Module)

Off

GSM module is Off.

Blinking

Fast

GSM module is On but is not registered with the network. (Network not
available)

Slow

GSM module is On and is registered with the network. (Network is available)

FXS

FXS Port is Off-Hook.

Off

FXS Port is On-Hook.

Blinking

FXS Port is ringing.

BAT

a. Battery (BAT) LED indication is applicable only for SIMADO GFX11E.

Battery is fully charged.

Off

Battery is absent.

Blinking

Fast

Battery is low.

Slow

Battery is charging.

Содержание simado gfx11

























































































Результаты поиска

Содержание simado gfx11

Отзывы:

Matrix simado gfx11, Системное руководство, Страница: 22 / 88

Результаты поиска

Содержание simado gfx11

Отзывы: