Martin Exterior 1200 Wash Скачать руководство пользователя | Manualshive

Страница: 56 / 84

background image

56

Exterior 1200 Wash user manual

8.1 Service: general

DANGER! Read "

Safety information"

on page 4 before servicing the Exterior

1200 Wash.

Important! The Exterior 1200 Wash requires regular service and
maintenance to maintain reliable operation and protect the investment it
represents.

Before servicing, switch off the lamp via DMX or the onboard control panel
and allow the luminaire to cool with fans running for 20 minutes before
powering off.

The service and maintenance procedures described in this section must be carried out by
qualified professionals only. Any service procedures not described in this section must be
carried out by Martin Global Service or its authorized agents.

8.2 Beam adjustment

The beam can be adjusted in a vertical plane (tilt) using the tilt lock on the yoke. The
beam can be adjusted in a horizontal plane (pan or rotation) using the curved slots in the
yoke base.

To adjust tilt:

1. Support the luminaire to ensure that

it cannot tilt unexpectedly under its
own weight. See Figure 16. Loosen
the tilt lock screws on each side of
the mounting yoke.

2. Tilt the luminaire to the desired

angle in the yoke and retighten the
screws to a torque of 16 Nm (11.8
ft.-lbs.).

To adjust pan:

1. Loosen the anchor bolts in the yoke

base slightly so that the luminaire
can be rotated.

2. Adjust the pan position and

retighten the bolts.

Figure 16: Tilt lock screws

«
...
54
55
56
57
58
...
»

Содержание Exterior 1200 Wash





















































































Отзывы:

Нет отзывов

Похожие инструкции для Exterior 1200 Wash

Бренд: A Little Lovely Company Страницы: 2

RS PRO DL LED 15W

Бренд: STEINEL PROFESSIONAL Страницы: 55

Бренд: XEPA Страницы: 24

Oktalite IN.VOLA

Бренд: Trilux Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 7

Бренд: GE Страницы: 2

Бренд: GE Страницы: 1

Arize Element Series

Бренд: GE Страницы: 7

Бренд: GE Страницы: 2

FCB-XM-3D-CH0078-120V

Бренд: GE Страницы: 2

Lumination LHSHX

Бренд: GE Страницы: 2

Lumination EP24 Series

Бренд: GE Страницы: 5

Бренд: GE Страницы: 2

LT-FCB-WF-5050-4W-30L-6M-Ex-C-RGB-120V

Бренд: GE Страницы: 5

FCB-XM-3D-MK0292-120V

Бренд: GE Страницы: 2

Бренд: Chauvet Страницы: 60

Бренд: LEX Lighting Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды