Martin Exterior 1200 Wash Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 84

background image

Physical installation

15

3 . 1 . 2 L o c a t i o n a n d m o u n t i n g

DANGER! Read "

Safety information"

on page 4 before attempting to install

this product.

Installation will probably be easiest if the lamp is installed before installing the luminaire
(see "

8.5.3: Installing the lamp"

Lifting

DANGER! Use only the lifting eyebolts provided to lift the luminaire.
Eyebolts must be securely installed with washers at all four corners of the
luminaire as illustrated below.

See Figure 2. The Exterior 1200 Wash is supplied with four eyebolts for lifting purposes
during installation or service. Do not use any other method to lift the luminaire. The
eyebolts screw into blocks in the yoke slider channels on each side of the fixture. Use the
supplied washers to avoid damage to the luminaire housing. Make sure that eyebolts are
firmly screwed in and will not slide in the channels before attempting to lift the luminaire.

Do not expose the eyebolts to undue stress while lifting, by allowing the luminaire to drop
and then catching it again, for example. Do not use the eyebolts for safety attachment.

Location and orientation

DANGER! The Exterior 1200 Wash mounting yoke base must be securely
anchored to a suitable flat surface. Ensure that the supporting structure can
bear the weight of all installed devices plus an adequate safety margin.

Consult a qualified engineer to determine a suitable anchoring method and to verify that
the structure can safely bear the luminaire’s weight.

Figure 2: Lifting eyebolts

«
...
13
14
15
16
17
...
»

Содержание Exterior 1200 Wash





















































































Отзывы:

Нет отзывов

Похожие инструкции для Exterior 1200 Wash

Бренд: Parkside Страницы: 35

Бренд: NightSearcher Страницы: 6

Бренд: Hülsta Страницы: 6

C-FL-A-LCF Series

Бренд: C-LITE Страницы: 6

Бренд: MARELD Страницы: 32

Бренд: Mark Страницы: 24

Бренд: ADJ Страницы: 14

Бренд: ANSMANN Страницы: 12

LEDA500 NW-BM Series

Бренд: Perel Страницы: 29

Бренд: Perel Страницы: 42

Бренд: JONATHAN Y Страницы: 2

Бренд: showtech Страницы: 20

SE1038-TBZ-01LF0-E

Бренд: ecolight Страницы: 4

SE1039-TBZ-02LF0-E

Бренд: ecolight Страницы: 16

Бренд: JMP Страницы: 5

Бренд: TI Страницы: 1

Бренд: ENHANCE Страницы: 24

Бренд: LDPI Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды