Martin Exterior 1200 Wash Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 84

background image

68

Exterior 1200 Wash user manual

8.8 Troubleshooting

Problem

Probable cause(s)

Remedy

No response from
luminaire when power is
applied.

No power to luminaire.

Check power cables.

Main or low-voltage fuse
blown.

Replace fuse.

Secondary fuse(s) blown
(located on PCB).

Refer to Martin Architectural.

Luminaire resets when
power applied but does
not respond correctly to
DMX controller. LED 2
lights steady green.

Incorrect DMX addressing.

Check luminaire addressing on
controller. If no error found, check
luminaire’s DMX address setting.

Luminaire resets when
power applied but does
not respond correctly to
DMX controller. LED 2
does not light steady
green.

Bad data link connection.

Inspect cables and correct poor
connections and/or broken cables.

Data link not terminated.

Insert DMX termination resistor in data
output of last luminaire on each branch of
the data link.

Luminaire resets when
power applied but does
not respond correctly to
DMX controller. LEDs
flash red and green.

Defective luminaire.

Bypass luminaires on the data link one at
a time until normal operation is regained.

Electronic or mechanical
failure.

Refer to Martin Architectural.

Luminaire software corrupted.

Upload new software. If luminaire
repeatedly fails to reset correctly, refer to
Martin Architectural for boot mode
upload.

Luminaire cuts out
intermittently, especially
in hot weather.

Luminaire temperature too
high: thermal cutout shutting
down power to avoid
overheating.

Stop using luminaire. Inspect for dirt
buildup and clean if necessary.
If luminaire is clean or if problem
reoccurs, stop using luminaire and refer
to Martin Architectural.

No light output.

Lamp has been in use and is
too hot to restrike.

Allow to cool for 8 minutes before
attempting to restrike.

Lamp defective or worn out.

Replace lamp.

Lamp cutout inside front cover
not correctly deactivated.

Open front cover. Make sure that left-
hand slider lock presses cutout switch.

Power settings do not match
local AC voltage and
frequency.

Disconnect luminaire and open rear
cover. Check jumper lead settings and
correct if necessary.

Temperature or fans error

Check display for error message. Check
for dirt buildup. Check that ambient
temperature does not exceed maximum.
Refer to Martin Architectural.

Lamp life unexpectedly
short (note that 3000
hours is

average

life, not

minimum

).

Defective lamp.

Replace lamp.

Strain on lamp or excessive
lamp strikes.

Always allow lamp to fully warm up for
five minutes before turning off.
Leave lamp powered and use intensity
command to reduce light output to zero if
only cutting light output for short periods.
Leave power applied for at least 8
minutes after switching off lamp to allow
cooling fans to reduce temperature.

«
...
66
67
68
69
70
...
»

Содержание Exterior 1200 Wash





















































































Отзывы:

Нет отзывов

Похожие инструкции для Exterior 1200 Wash

Бренд: Westinghouse Страницы: 4

Бренд: Goobay Страницы: 6

Бренд: Stairville Страницы: 52

Бренд: ADJ Страницы: 4

Бренд: Emos Страницы: 16

Бренд: PR Lighting Страницы: 26

Бренд: Deluce Lighting Страницы: 2

Бренд: Mark Страницы: 16

Бренд: LumiSource Страницы: 1

Home Easy HE-403

Бренд: Byron Страницы: 2

VANA LED S PROFI PN32300009

Бренд: Panlux Страницы: 2

Бренд: Husky Страницы: 5

Бренд: WE-EF Страницы: 7

Бренд: AEG Страницы: 8

Бренд: Philips Страницы: 4

Lytespan 23S20P3

Бренд: Philips Страницы: 2

Lytespan 23MHRS

Бренд: Philips Страницы: 2

Lytespan 23S20MR

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды