Martin Exterior 1200 Wash Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 84

background image

28

Exterior 1200 Wash user manual

• set up the luminaire’s DMX address so that commands can be sent to a specific

luminaire from a DMX controller

Display

When the luminaire is powered on, the control panel displays information about the
luminaire in two lists that it switches between approximately every 5 seconds:

• The

F ix t u r e s t a tu s

list displays information about luminaire temperature and fan

speed in RPM (revolutions per minute)

• The

La m p s t a tu s

list displays a list of resettable counters that indicate hours of lamp

use, number of times the lamp has been struck (powered on) and number of times the
luminaire has been powered on.

Control panel

The display and control buttons are protected by a clear cover that is secured with Allen
screws. Remove the cover for access to the control buttons and replace it when access is
no longer required.

Use the control panel buttons as follows:

• Use the

Menu

button to open the menus or to navigate one level higher up in the menu

structure.

• Use the

Enter

button to open a sub-menu, confirm a command or set a value.

• Use the

Up

and

Down

buttons to move up and down a list, toggle between options or

increase and decrease a value.

By default, the display backlight goes out automatically 2 minutes after the lamp is turned
on. The backlight returns to its preset intensity level as soon as a control button is
pressed, or in the event of an error or warning message.

A backlight can be switched on, making the display easy to read in the dark, via the

Se t

b a c kl i g h t l e v el

command in the

P e r s on a l it y

menu. The brightness of the display

can be adjusted from 100 (maximum) to zero (off).

9.3: Onboard control panel menus"

on page 74 for a complete overview of the

options available in the onboard control panel.

Self-diagnostic feedback messages

In the event of a problem, the Exterior 1200 Wash will show a message in the display
indicating the type of problem that has occurred.

4 . 1 . 6 C o o l i n g f a n s

When power is applied, cooling fans run at full speed for a few seconds to clear any dust
that has accumulated in the heat exchanger. After this, fan speed is regulated
thermostatically to maintain an even temperature in the luminaire. When the lamp is
switched off without cutting power to the luminaire, fans remain active.

4 . 1 . 7 O p e r a t i n g i n h o t e n v i r o n m e n t s

If the ambient temperature is above 30° C (86° F) or if the luminaire will be exposed to
strong sunlight, leave the luminaire powered on – but with the lamp powered off – when
not in use. This will keep the cooling system running and control the luminaire’s internal
temperature.

«
...
26
27
28
29
30
...
»

Содержание Exterior 1200 Wash





















































































Отзывы:

Нет отзывов

Похожие инструкции для Exterior 1200 Wash

Crouse-Hinds FMV Series

Бренд: Eaton Страницы: 3

Бренд: jcb Страницы: 8

Бренд: Raspa Страницы: 5

Бренд: PR Lighting Страницы: 34

Бренд: EuroLite Страницы: 2

Бренд: HQ Power Страницы: 35

Бренд: Oemtools Страницы: 4

Бренд: CREE LIGHTING Страницы: 6

StarCluster 3270

Бренд: Kaiser Страницы: 18

EPLC2-MB-100LED-100

Бренд: Larson Electronics Страницы: 4

Бренд: Hama Страницы: 28

Бренд: Rebel Light Страницы: 2

Бренд: Rebel Light Страницы: 12

M-22PL-840-R14-WFL

Бренд: Maximus Страницы: 12

Бренд: Verde Energy Group Страницы: 3

Бренд: Parkside Страницы: 40

Бренд: Coemar Страницы: 23

Infinity Spot XL

Бренд: Coemar Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды